www亚洲视频-www亚洲色图-www亚洲精品-www亚洲国产-青青草99热这里都是精品-青青草99热久久

Language:CHINESESENGLISH

Home > News > steel welding engineering
CONTACT US
  • Address:Pingtang Industrial District, Shipeng Village, Shishan Town, Nanhai District, Foshan City,
  • Phone:0757-81002668/0757-63323396
  • Fax:0757-81196682
  • Contact:Ben Zheng/13826981293 Kerry Lu/13751224830
  • E-mail:sbs@sbsprefabhouse.com
  • URL:http://www.huihuitaotao.cn

steel welding engineering

Time:[2016-1-23]  Hits:4919

Guangzhou Steel teach you: steel welding engineering

(A) material quality requirements
(1) Canton steel welding works with a welding rod, wire, flux, electroslag weld mouth, studs, welding porcelain ring and shielding gas welding, etc. must be used with a factory quality certification, quality inspection reports and other documents.
(2) Guangzhou steel welding engineering, the general principles of the weld metal and base the selection of materials, such as strength of welding rod, wire, solder and other welding materials.
(3) welding, flux cored wire, electroslag weld mouth and studs with ceramic ring before use, must be baked in accordance with the provisions of the product description and related welding processes.
(Ii) quality control during construction
(1) When the welding operations ambient temperature is below 0 ℃ but not lower than -10 ℃, welded joints and welding surface should be in each direction is greater than or equal to 2 times the plate thickness range of not less than 100mm is heated to not lower than 20 ℃ After the minimum preheat temperature specified above and before welding, and the welding process should not be below this temperature.
Room (2) pre-heating and temperature control channels should adopt electric heating, flame heating and infrared heating plus heat method, and using special thermometer measurements. Preheat the welding area should be heated on both sides of the groove width of more than 1.5 times the thickness of the weldment welding, and not less than 100mm. Temperature measurement point, when non-members should be on the back of an enclosed space heating surface in the weldment from both sides of the weld groove at not less than 75mm, when the member is a closed space should be in the front side from the weld groove at not less than 100mm. When the process of selection of the preheating temperature is below the minimum specification requirements should be determined by the procedure qualification test.
(3) non-sparking arc welds on the base metal outside the area. In the groove arc welding a local area should not be leaving the crater. When the arc plate, lead plate and spacer plate when the steel should be used in the yield strength of not more than the nominal strength steel is welded steel, and weldability similar.
(4) The multilayer welds should be continuous welding, weld bead after each layer should be cleared up.
(5) Such as design documents or the contract documents required butt eliminate stress, the structure of the tensile stress fatigue check node butt or weld-intensive, member, should adopt the electric heater and partial annealing furnace annealing overall and other methods of stress relief treatment; if only stable structure size, vibration method can be used to eliminate stress.
(6) with a hammer method to eliminate intermediate solder layer stress, you should use the network first hand hammer or a small vibrating tool, should not be the root of the weld, the weld cap weld or bevel edge of the base material hammer.
(7) carbon steel welds should be cooled to ambient temperature, low-alloy steel should be after the completion of the welding seam 24h NDT testing.
(8) checks should be carried out after bending test weld stud welding, stud weld and heat affected zone bend 30 ° after there is no visible cracks.
(9) the repair welds should be continuous welded parts, should be taken if an interrupt after welding heat insulation measures to prevent cracks; repairing defects in the weld of the same parts of the number should not be more than twice the area of ​​welded joints should be increased after the repair powder or colored checks.

Copyright:佛山市勝邦鋼結構有限公司 Foshan Shengbang Steel Structure Co., Ltd. Record Number:粵ICP備13078463號
主站蜘蛛池模板: 襄阳燃烧器厂家-低氮燃烧器价格-河北五通道燃烧器就找襄阳市胜合燃力设备有限公司一站式服务 | 临沂网站建设,临沂网站制作,临沂网络公司,临沂小程序开发,临沂网站设计,沂水网站建设,沂南网站建设,蒙阴网站建设,平邑网站建设,费县网站建设,兰陵网站建设,郯城网站建设,临沭网站建设,莒南网站建设,兰山网络公司 | 铸铁型材_灰铁棒_球铁棒_圆铁棒生产厂家★河北起昌精密装备制造有限公司 | 中商信息网-商务数据网-中文商务数据网| 义乌供需网-义乌外发加工来料加工,义乌采购信息供求对接平台(yiwugongxu.com) | 中国C919飞机橡胶接头供应商-上海淞江减震器集团有限公司官方网站 | 环保除尘设备_燃气/燃油热水锅炉_光氧空气净化器_蒸汽玉米压片机_压片设备_烘干设备-山东金盾节能环保设备有限公司 | 钻机配件-岩心管-岩心管接箍-地质套管-煤矿用钻头-河南滨远机械设备有限公司 | 噪声治理,消声器,隔声屏障,隔声罩,噪声控制,降噪,空调降噪,水泵噪声治理,冷却塔噪声治理-北京华清恒业环保设备有限公司 | 活性炭吸附设备,UV光氧废气处理设备,破碎机专用除尘器,催化燃烧设备厂家-河北碧清环保设备有限公司 | 潍坊晨硕机械设备有限公司| 外墙涂料_真石漆_真石漆批发_河南宝润达真石漆厂家 | 西安logo设计公司/西安包装设计公司/西安画册设计公司/西安广告公司/西安品牌设计公司/泰勒广告 雾度计-雾度仪-透光率测试仪-3nh品牌雾度仪生产厂家 | 免费会员管理系统,会员管理软件,会员卡积分系统—智络软件 | 永康风水大师选风水先生老徐 - 徐根法 | 全自动灌装机械设备-迈驰粉末/颗粒/液体/膏体灌装机械设备流水线生产厂家 | 西安墓园-山水殡葬服务-提供免费墓地咨询服务 | 旋风铣_数控旋风铣整机_旋风铣头|定制生产厂家【腾创机械厂官网】 | 蒸汽发生器-电加热蒸汽发生器、燃油蒸汽发生器、燃气蒸汽发生器设备厂家-诺贝思蒸汽发生器 | 中国(北京)国际园林绿化设备展览会 | 氧化膜测厚仪-瓶壁测厚仪-QNIX菲尼克斯膜厚仪-深圳市时代之峰科技有限公司 | 铁谷网-垂直于铸造产业链服务平台、原材料采购网、行业资讯网 | 双螺杆挤压膨化设备_挤压熟化设备_烘干设备_油炸设备及喷涂调味设备-山东铭本机械科技公司 | 景德镇市奥群包装材料有限公司| 久久91精品久久91综合_国产亚洲自拍一区_国产精品第1页_亚洲高清视频一区_91成人午夜在线精品_亚洲国产精品网站在线播放_亚洲国产成人久久综合区_国产精品亚洲专区在线观看_免费视频精品一区二区三区 | 合金锤头_破碎机锤头_耐磨锤头_巩义市东辰实业有限公司 | 文件管理系统-文件管理软件-文档管理系统-文档管理软件-档案管理系统-档案管理软件 - 致得软件 | 聚达|聚达物联|聚达物联科技|杭州聚达物联科技有限公司|www.judawulian.com|智慧社区|数字驾驶舱|智慧清运|智慧工地|邻家小达 | 烧碱-工业片碱-火碱价格-氢氧化钠厂家-巩义市宝莱新材料厂 | 指挥调度|调度系统|应急指挥调度|应急指挥|可视化调度|多媒体指挥调度|融合通信|综合调度|应急指挥系统|IP调度系统-北京瑞光极远数码科技有限公司 | 转炉挡渣机构,转炉滑板挡渣,滑动水口生产厂家-河北瑞华冶金科技有限公司 | 山东向阳电子科技有限公司-多用户集中式电能表生产厂家,NB物联网水表,刷卡水电表生产厂家,泰安智能水电表价格 | 清洁公司| 保洁公司| 东莞清洁| 东莞保洁|壹壹清洁 | 郑州冷却塔_河南冷却塔-河南金创制冷设备有限公司 | 停车场设计|地下停车场规划设计|智能停车位地下车库设计施工装修|深圳创安顺停车库规划设计有限公司 | 硫酸、硫酸铵、氯磺酸、氯化亚砜、硫酸钾、对位酯生产销售 - 河北和合化工有限公司 | 压滤机_板框压滤机_生产厂家陕西华星佳洋装备制造有限公司 | 鸿茗商务-杭州鸿茗商务咨询有限公司 | 液体灌装机-酱料灌装机-全自动灌装机-旋盖机-铝箔封口机-贴标机厂家-迈特威自动化设备(天津)有限公司" | 氧化膜测厚仪-瓶壁测厚仪-QNIX菲尼克斯膜厚仪-深圳市时代之峰科技有限公司 | 戒网瘾学校-陕西正规戒网瘾-叛逆青少年教育学校-重生教育官网 |